Hệ thống điều khiển Nireco AE1000 – Nireco Viet Nam liên hệ
Hệ thống điều khiển Nireco AE1000 – Nireco Viet Nam
ID: G-0010505-00223
Công ty TNHH Thương Mại Và Dịch Vụ Tăng Minh Phát (TMP Vietnam) là nhà phân phối của hãng Nireco tại thị trường Việt Nam, chuyên về các thiết bị như cảm biến lực căng, cảm biến chỉnh biên, máy dò sản phẩm lỗi trên băng chuyền,…
Hãy liên hệ với chúng tôi để được hỗ trợ tốt nhất !
Trần Công Lên
Tel: 0906.765.489 – 0914.573.068
Email: [email protected]
[email protected]
Liteguide Controller AE1000
Overview
The Liteguide Controller AE1000 carries out EPC （Edge Position Control） through a combination of Photoheads （PH16B） and Ultrasonic Sensor （UH01）, CPC （Center Position Control） through a combination of Photoheads and Autowide Sensor （AWE280 etc.） and LFC （Line Follower Control） through a combination of LH19 and LH110.
Feature
- Liteguide Controller AE1000 is the successor to the previously well established AE900E and AE900L controllers.
- This single type can be connected to Nireco standard sensors which has been used with the AE900E or AE900L controller.
（Some sensors may need to be used with a preamp） - Can be used directly coupled with electrical actuators K12 and K61. Can also be connected to the K80 series through use of a driver.
- Has 2 systems, a sensor input stage and a shift input stage, which can be switched for use.
- Uses a larger LCD display than previous models with a white backlight making it both easier to see and allowing for verification of a greater amount of information.
Configuration
Specifications Power Supply VoltagePower ConsumptionPower FuseAmbient Operating TemperatureAmbient Operating HumidityVibration ResistancePower supply NoiseUsage atmosphere:MassIP ClassInput2 Sensor systems2 analog shift systemsCenteringPosition TransmitterPhoto coupler input
（12V DC, 15mA）OutputElectrical actuatorLamp power sourceFine tuner, Position transmitter, LH8BSensorsCentering proximity switch power source2 indicator systemsPhoto coupler output
（24V DC, 40mA）
| AC100 to 240V 50/60Hz ±10% |
| 300 VA (inrush current 100 A 10 ms typical (200 V)) |
| 250V AC, 3.15 A (time-lag type) |
| 0 to 50°C |
| 35 to 85% RH or lower (no condensation) |
| 3.5 mm, 1 G, 3 to 150 Hz, three-directions (1hour) |
| 2.5 kVp-p, normal mode, common mode 50 ns, 1μs width |
| Area with no water, flammable or corrosive gases, and little dust. |
| Approximately 5 kg |
| IP30 |
| Voltage input Maximum ±5V（No input resistance） Current input 0-20mA (input resistance converted to 240/2kΩ) |
| Voltage input Maximum ±10V |
| Proximity switch input （0-8V, 1.2kΩ input resistance）（Applies to: KL1632. 0-90P） |
| Voltage input Maximum ±10V |
| Remote controller : Operation mode switching（auto / manual / centering） Operation keys （left / right / auto balance / reverse） System selection（EPC1 / EPC2） Locks 3 points Actuator end limit : 2 points |
| K12 ±24V DC, 1A(maximum) or K62 ±36V DC, 2A(maximum) |
| 4 to 12V DC, variable （maximum 1A） |
| ±5V power source （maximum 0.1A） |
| ±15V power source （+15V, 1A; -15V, 0.2A） （Note: The current capacity on the + side combined with the lamp power source in(2) is less than 1A.） |
| 8V DC （maximum 30mA） |
| Voltage output Maximum ±10V （load resistance 2kΩ or greater） Deviation output Position transmitter output |
| Remote controller : Operation mode state（auto / manual / centering） System state （EPC1 / EPC2） Alarms Excessive deviation End limit Actuator lock Actuator excessive load |
Liên hệ mua sản phẩm
(Trong khuôn viên Tổng Công Ty Thái Sơn - Bộ Quốc Phòng)
Điện thoại: 028 6658 9888
Email: [email protected]
