CLA-VAL: Van giảm áp (pressure reducing), van an toàn (relief valve), điều chỉnh lưu lượng (flow control), xả khí (air vent), deluge valve, van 1 chiều (check valve), van phao (float valve)
1/- The Cla-Val Model 90-01/690-01 Pressure Reducing Valve automatically reduces a higher inlet pressure to a steady lower downstream pressure, regardless of changing flow rate and/or varying inlet pressure. This valve is an accurate, pilot-operated regulator capable of holding downstream pressure to a predetermined limit. When downstream pressure exceeds the pressure setting of the control pilot, the main valve and pilot valveclose drip-tight.
2/- The Cla-Val Model 50-01/650-01 Pressure Relief Valve is a hydraulically operated, pilot-controlled, modulating valve designed to maintain constant upstream pressure within close limits. This valve can be usedfor pressure relief, pressure sustaining, back pressure, or unloading functions in a by-pass system.
3/- The Cla-Val Model 40-01/640-01 Rate of Flow Control Valve prevents excessive flow by limiting flow to a preselected maximum rate, regardless of changing line pressure. It is a hydraulically operated, pilot controlled, diaphragm valve. The pilot control responds to the differential pressure produced across an orifice plate installed downstream of the valve. Accurate control is assured as very small changes in the controlling differential pressure produce immediate corrective action of the main valve. Flow rate adjustments are made by turning an adjusting screw on the pilot control.
4/- The Cla-Val Series 34 Air Release Valve is designed to protect pipelines from entrained air that collects at highpoints in a pipeline. This valve continuously eliminates air from a system by releasing small amounts of air before large air pockets can occur. In extreme cases, the continued accumulation of air without release valves can actually stop flow completely. Increased power consumption and associated power costs can be anticipated if systems are not properly designed to release accumulated air
5/- The Cla-Val Model 55L (UL Listed FM approved) Pressure Relief Valve is a direct-acting, spring loaded, diaphragm type relief valve. The valve may be installed in any position and will open and close within very close pressure limits.
6/- Cla-Val “Tite Seal” foot valves provide years of trouble free operationat low or high pressures.
7/- The Cla-Val Model 134-05 Solenoid Control DELUGE Valve is an on-off control valve which either opens or closes upon receiving an electrical signal to the solenoid pilot control.
8/- Cla-Val Series 501A Wafer Swing Check Valve has a quick, spring-assisted closure that minimizes the possibility of water hammer.
9/- The Cla-Val Model 8124-01 Float Valve is a non-modulating valve that accurately controls the liquid level in tanks. This valve is designed to openfully when the liquid level reaches a pre-set low point and close drip-tight when the level reaches a preset high point.
10/- Designed to protect pipelines from air lock and vacuum collapse, the Cla-Val Model 33A Air Release and Vacuum Breaker Valve eliminates air and prevents vacuum formations in pipelines. It hasa large venting orifice and large float clearances to freely exhaustor admit air during pipeline filling or draining.
Vui lòng liên hệ
HỒNG ANH TUẤN
0918.119.223 / 0905.532.592
FORD METER BOX: Angle Meter valve, Corporation Stop, Saddle, Repair Clamp, Coupling, Drilling machine, Flange adapter, Test Bench
PEKOS steel ball valve
Control valve, angle seat valve, SLIDING GATE, PINCH VALVE
Van điều khiển tự động - van giảm áp, an toàn, deluge
CLA-VAL: Van giảm áp (pressure reducing), van an toàn (relief valve), điều chỉnh lưu lượng (flow control), xả khí (air vent), deluge valve, van 1 chiều (check valve), van phao (float valve)
PPP: water hammer arrestor, tempera valve, trap primer, thermostatic and balancing valve
GSR: Van solenoid, angle-seat valve (van góc)
(Trong khuôn viên Tổng Công Ty Thái Sơn - Bộ Quốc Phòng)
Điện thoại: 02862.761612 - 02862.757416 - 090 315 0099
Email: [email protected]