Epoxy Resin FLOORING
INTRODUCTION
Rockmax Supercote 1 is two components solvent based epoxy coating use for concrete and steel protection. Design for light to medium resistance for both walls and floors. Its provide gloss, seamless and smooth finish which easily cleaned.
AREA OF USES
ADVANTAGES
APPLICATION AND INSTALLATION
PREPARATION
Concrete must be sound, clean and free from cement paste, dust, dirt and any other contaminants. Concrete must be at least 28 days and minimum compressive strength 25N/mm2 and minimum tensile strength (pull off) at 1.5 N/mm2. The concrete moisture content must less than 4%.
PRIMING
Apply Rockmax Supercote P prior to apply body coat. For steel structure, please contact Rockmax for further information.
MIXING
Mix part A and part B approximate 3 minutes until homogeneous using electric mixer (400-500 rpm).
APPLICATION
Apply by brush or roller on the prepared surface. Wait until dry 24 hours prior to apply second coat.
CURING
Protect applied areas from foot traffic at approximate 24 hours and fully cure in 7 days.
PACKAGING
20 kg set.
INTRODUCTION
Rockmax Supercote 3 is two components solvent free epoxy coating. Its design for medium chemical and mechanical resistance. When cured it formed Good texture finished, seamless and gloss.
AREA OF USES
ADVANTAGES
APPLICATION AND INSTALLATION
PREPARATION
Concrete must be sound, clean and free from cement paste, dust, dirt and any other contaminants. Concrete must be at least 28 days and minimum Compressive strength 25N/mm2 and minimum tensile strength (pull off) at 1.5 N/mm2. The concrete moisture content must less than 4%.
PRIMING
Apply Rockmax Supercote P prior to apply body coat. For steel structure, please contact Rockmax for further information.
MIXING
Mix part A and part B approximate 3 minutes until homogeneous using electric mixer (400-500 rpm).
APPLICATION
Apply by brush or roller on the prepared surface. Wait until dry 24 hours prior to apply second coat.
CURING
Protect applied area from foot traffic at approximate 24 hours and fully cure in 7 days.
CLEANING
Clean all tools and equipments immediately with acetone, xylene, thinner or solvent.
PACKAGING
20 kg set
INTRODUCTION
Rockmax Supercote 5 is a water dispersed two component epoxy resin coating system. Design for durable coating for walls and floors include can be applied on damp surface. Ideal for use as coating where solvent based material are not allowed.
AREA OF USES
ADVANTAGES
APPLICATION AND INSTALLATION
PREPARATION
Concrete must be sound, clean and free from cement paste, dust, dirt and any other contaminants. Concrete must be at least 28 days and minimum Compressive strength 25N/mm2 and minimum tensile strength (pull off) at 1.5 N/mm2. Pre wet surface if necessary.
PRIMING
Dilute Rockmax Supercote 5 with 10% clean water to help good penetration for concrete substrate. Apply by roller or brush and wait 24 hours until dry.
MIXING
Mix part A and part B approximate 3 minutes until homogeneous using electric mixer (400-500 rpm).
APPLICATION
Apply by brush or roller on the prepared surface. Wait until dry 24 hours prior to apply second coat and third coat.
CURING
Protect applied area from foot traffic at approximate 24 hours and fully cure in 5 days.
CLEANING
Clean all tools and equipments immediately with clean water.
PACKAGING
20 kg set.
INTRODUCTION
Rockmax Supercote SL is a two components 100% solid epoxy resin floor topping. This product provides a high gloss, smooth, seamless, hygienic, durable and hard wearing. Rockmax Supercote SL designed for application 1-3mm thickness and suitable with industrial and commercial application.
AREA OF USES
ADVANTAGES
APPLICATION AND INSTALLATION
PREPARATION
New concrete substrate
Concrete must be sound, clean and free from cement paste, dust, dirt and any other contaminants. Concrete must be at least 28 days and minimum Compressive strength 25N/mm2 and minimum tensile strength (pull off) at 1.5 N/mm2. Moisture content in concrete must less than 4%. All floors to received Rockmax Supercote SL topping should be protected by damp proof membrane. Total enclosed shot blasting or scarifying should be employed followed by vacuuming.
Old concrete (Uncoated concrete)
Old concrete or uncoated concrete floors is done in much similar manner to new concrete preparation. The concrete surface must be thoroughly cleaned with a strong detergent cleaner to remove all grease, oils and etc. Holes and cracks must be repaired use epoxy injection and epoxy mortar (please consult Rockmax for more information).
Previously coated concrete surface
Existing coated surface must be completely removed by sand blasting until received sound surface. Clean all surface with detergent cleaner. Total enclosed shot blasting or scarifying should be employed followed by vacuuming.
PRIMING
Apply Rockmax Supercote P at 1 or 2 coat. Allow to dry prior to application. Please refer Rockmax Supercote P datasheet.
MIXING
Stir each component separately approximate ½ to 1 minute. Mix part A and part B approximate 3 minutes until homogeneous using electric mixer (400-500 rpm). Avoid whipping air into the material. It is recommended that only full units be used, that both components are thoroughly mixed. We do not recommend using partial kits and reduce material.
APPLICATION
This material must be applied by specialist trained applicator. Pour mixed material directly on the surface in a long puddle and spread using either trowel or rubber squeegee. Pull through material until end of joints. Pour new material on to end of joints to maintain wet edge. Check film thickness frequently. Use spike roller to remove any entrapped air. Do not spike roller after 30 minutes.
CURING
Protect applied areas from foot traffic at approximate 24 hours and fully cure in 7 days.
CLEANING
Clean all tools and equipments immediately with acetone, xylene or other solvents.
PACKAGING
20kg set:
Part A: 16kg
Part B: 4kg
INTRODUCTION
Rockmax Supercote P is two components solvent based epoxy clear primer and surface treatment to porous concrete.
AREA OF USES
Primer for Rockmax Supercote coating on concrete substrate walls and floors.
ADVANTAGES
APPLICATION AND INSTALLATION
PREPARATION
Concrete must be sound, clean and free from cement paste, dust, dirt and any other contaminants. Concrete must be at least 28 days and minimum Compressive strength 25N/mm2 and minimum tensile strength (pull off) at 1.5 N/mm2. The concrete moisture content must less than 4%.
MIXING
Mix part A and part B approximate 3 minutes until homogeneous using electric mixer (400-500 rpm).
APPLICATION
Apply by brush or roller on the prepared surface.
CLEANING
Clean all tools and equipments immediately with acetone, xylene, thinner or solvent.
PACKAGING
15 kg set.
INTRODUCTION
Rockmax Supercote PS is a two components polyamide for protect metal and steel from rust.
AREA OF USES
Primer for Rockmax Supercote 1 & 3 coating on steel and metal.
ADVANTAGES
APPLICATION AND INSTALLATION
PREPARATION
Sound and clean steel surface. Make sure no rust and dust on the surface.
MIXING
Mix part A and part B approximate 3 minutes until homogeneous using electric mixer (400-500 rpm).
APPLICATION
Apply by brush or roller on the prepared surface.
CLEANING
Clean all tools and equipments immediately with acetone, xylene, thinner or solvent.
PACKAGING
15 kg set
CHẤT CHỐNG THẤM
CHẤT TRÁM
VỮA SỬA CHỮA BÊ TÔNG
VỮA TĂNG ĐỘ CỨNG
BĂNG CẢN NƯỚC
Floor Hardener & Dust Proofer FLOORING
Epoxy Resin FLOORING
PU FLOORING-Polyurethane Resin
Cảm ơn Quý khách đã quan tâm đến sản phẩm trên.
Hiện tại tài khoản doanh nghiệp đăng sản phẩm trên chưa được xác thực.
Để mua sản phẩm, Quý khách vui lòng liên hệ chi tiết theo địa chỉ: , hoặc Email: [email protected]
Trân trọng.
(Trong khuôn viên Tổng Công Ty Thái Sơn - Bộ Quốc Phòng)
Điện thoại: 02862.761612 - 02862.757416 - 090 315 0099
Email: [email protected]
